How To Repair Broken Eyeglass Frame

Download Commodity

Download Article

Breaking your eyeglasses tin can be frustrating, and you might not always be able to replace them right away. Whether you lot scratched the lense, lost a spiral, or broke the span, you tin can repair your eyeglasses yourself to hold yous over until you are able to get a new pair.

1. i

   Use the mucilage-and-paper method. For an constructive temporary set up, it is possible to mucilage your eyeglass dorsum together to repair a break at the bridge (the office that goes over your nose).

   • Clean. Make sure that the two pieces you're trying to glue are clean. (Remove all glue from previous attempts. If it'southward "super gum", fingernail polish with acetone will piece of work but it's tough on the frames)^[1]
   • Get your supplies in place. Gather up the post-obit: Super Glue (Locktite, Krazy Glue, etc), pieces of glossy wrapping paper or thick magazine pages that friction match your frames, abrupt scissors
   • Cut the wrapping paper into thin strips approximating the width of your frames.
   • Glue the paper to your frames, 1 strip at a time. Use a brusque slice of paper as a splint across a broken nosepiece or wrap a longer piece around similar an ace bandage.^[2]
   • Look for each slice to dry before you add the next

   Advertisement

1. 1

   Get your materials in identify. Y'all'll need a thread, needle, drill, sandpaper, superglue, painter'southward stir stick, safety bands, waxed paper, cotton fiber swabs, alcohol or smash polish remover and a hobby pocketknife.

2. 2

   Clean and sand the broken pieces. Use sandpaper to clean and rough up the broken surface area to exist glued. Swab the area with some rubbing alcohol or nail smoothen remover to ready the surface.

3. 3

   Secure the 2 pieces together. Cutting a piece of a painter's wooden stir stick to fit between the temples (aka, the side pieces) of your spectacles. Comprehend your lenses with wax paper to forbid scratching and and so wrap a prophylactic ring over i cease of the stick and secure it to your spectacles. Do the same on the other finish.

   • Line the two halves up carefully and exist sure the safe bands are holding things firmly in place. If it wasn't a clean intermission and there are some gaps, line the pieces up every bit best you can taking pains to ensure there are some definite points of contact.^[three]

4. 4

   Glue. Fill up the joint at the break with glue; apply enough to secure the bridge but not so much that the glue runs out. Squeeze out the glue slowly and neatly to avert bubbles. Every bit you fill in the articulation, be certain that there are no gaps or voids. Use the side of a cotton swab to gently make clean up any excess gum; swab information technology upward before it has a chance to dry out and get tacky. Set the spectacles aside for at least an hr so the glue tin dry completely.

5. five

   Drill two holes. Cull a small drill bit appropriate for the thickness of your eyeglass frames. Take your hobby knife and dig out pilot holes on either side of the newly repaired joint. Identify your glasses downward on a soft cloth that'due south been laid on a tabular array peak and carefully drill a hole on each side of the suspension. The holes must be parallel so they can be used to wrap a band of thread effectually the core articulation.^[4]

6. 6

   Sew a tension ring in identify. Use a fine needle and 4 to six feet of thread that matches the color of your eyeglass frames to "sew" the two sides of the repair together for added strength. Laissez passer the needle and thread through the two holes as many times every bit you can taking care non to pull besides hard and put stress on the newly repaired joint. Stop when at that place's no more than room. Fill the drilled holes with glue, soaking the thread and blotting up any excess with a cotton swab. Trim the edges of the thread and allow the glue to dry for at least an hour.

7. vii

   Add together a wrap. If you want to requite actress forcefulness to your repair, you can add this boosted step to your process. Do not trim the edges of the thread every bit above. Instead, after your glue has dried, accept the remaining thread from one side and wrap it around the bridge of your glasses from front to back. Make your wrap as neat as possible; some criss-crossing may be unavoidable, only do your best to preclude the wrap from looking bulky. Leave a short end to exist trimmed afterwards. Soak the wrap with glue and let it dry out for ten-xv minutes. Accept the thread from the other side of your glasses and wrap it effectually the bridge in the opposite direction (back to forepart). Soak the new wrap in glue and let information technology cure for a couple of minutes before snipping off the two loose ends. Gear up your glasses aside for 24 hours earlier wearing.

   Advertizing

1. 1

   Boil h2o. Fill a pocket-size pot with water and set the flame to "high." Considering you're going to use oestrus for this repair, the frames of your glasses must exist plastic for it to work.

2. 2

   Melt the plastic. One time the water is boiling, hold the broken edges of the glasses over the pot and close plenty for the heat to soften the edges.

3. three

   Insert a pin. Push a curt pin into ane border and and then push the other border onto the pin. While the plastic is still hot, smoothen it over the pivot. ^[5]

   • Never put plastic eyeglass frames straight over a flame.

   Advertisement

1. ane

   Use an eyeglass repair kit. Eyeglass repair kits are readily available at drugstores and contain everything you need to make a repair--screws, a tiny screwdriver and sometimes a magnifying drinking glass. A newer version of the kit contains longer screws meant to be easier to handle. You insert the screws into the hinges, screw them in and then "snap off" the bottom of the spiral to fit the size of the hinge.

   • If you're finding it difficult to line up the hinges on your temple piece and front piece, it could considering a hinge mechanism inside the temple piece hinge is belongings it back. To right this, use the hook end of a paper clip, insert information technology through the temple hinge hole and gently pull it out. To keep the hinge hole in place, insert a second paperclip upright and into the "gap" created when you pulled out the hinge hole. Line upward the forepart slice and temple piece holes and insert and tighten the spiral. When you're finished, remove the paperclip from the gap and the hinge hole will slide back into place creating a firm fit for your glasses. ^[6]

2. two

   Try a toothpick. When a screw falls out of the swivel that holds the front and temple pieces of your spectacles together, use a toothpick to temporarily take the place of the screw. Line up the temple hinge holes with the front holes and push a wooden toothpick through them as far equally information technology will go. Interruption or clip off the excess.^[seven]

3. 3

   Substitute with a wire. Strip the paper off of a twist tie (the kind that come on a bag of bread). Line up the hinge holes and thread the twist-tie wire through them. Twist the wire in place until the temple feels secure. Cut off the edges of the wire and so you don't get scratched. Yous can also utilise a small safe pin (the ones that are sometimes used with clothing price tags). Insert the pin through the holes to hold the side in place.

   Ad

1. 1

   Use baking soda and water. Commencement, wipe off both your lenses with a microfiber cloth. Next, mix i teaspoon (iv.9 mL) of water with 1 tablespoon (fifteen mL) of baking soda until it forms a paste-like consistency. Then, apply the paste to your lenses and gently scrub your lenses with the substance. After, rinse your glasses with water to launder off the blistering soda mixture. This volition likely exist all yous need to remove the scratches!^[viii]

2. 2

   Utilize a household cleaner. Abrasive cleansers tin can exist used to smoothen scratched surfaces. Waxy products like Lemon Pledge and Carnauba cleaner wax actually fill light scratches with wax. However, the wax volition reduce your visibility and require reapplication every few days. You can also try rubbing alcohol or diluted ammonia. After treating your spectacles with one of these products, polish them with a soft cloth, ideally i fabricated especially for cleaning glasses.

3. iii

   Forestall hereafter scratches. Lenses are delicate and should be treated with care to forestall them from getting scratched.

   • Use an eyeglass case. A sturdy, cushioned case will protect your eyeglasses; place them in a instance rather than in your pocket or throwing them directly into your bag.^[ix]
   • Wash your lenses. Make clean your spectacles every day with soapy h2o and dry them with a make clean, soft cloth made for this purpose.
   • Stay away from unfriendly products. Some products can harm your lenses and should exist avoided. Don't use facial tissues or paper towels to clean your lenses and stay abroad from anti-bacterial soaps when y'all wash them.^[10] Exist careful when using hairspray, perfume or blast polish remover--they can remove the coatings on lenses.

   Advertizing

Ask a Question

200 characters left

Include your electronic mail address to become a bulletin when this question is answered.

Submit

Advertizing

Video

• Go along gum away from your lenses and your fingers

• In a pinch, the become-to method for fixing a broken span is simply to wrap tape around it to hold the two pieces in place. Cull a color tape that matches the color of your frames most closely or make a style statement and wrap them in a piece of decorative duct record.

• If a white residue develops on the frames from contact with acetone, try rubbing them with an oil based balm.

Advertisement

• Keep glue away from eyes until completely dry

Advertising

About This Article

Article Summary Ten

If you lose a screw from your glasses, try purchasing an eyeglass repair kit from a drugstore. These have replacement screws and a tiny screwdriver to make the repair easy. If you can't find a repair kit, push button a wooden toothpick through the hinge holes. You can too wrap a thin piece of wire through the holes and twist it until the temple of your glasses feels secure. If your glasses have a broken bridge, keep reading to larn how to fix it yourself.

Did this summary help you?

Cheers to all authors for creating a folio that has been read 752,438 times.

Did this article help yous?

Source: https://www.wikihow.com/Repair-Eyeglasses

Posted by: penafavy1978.blogspot.com

Share this post